? semiconductor components industries, llc, 2006 november, 2006 ? rev. 10 1 publication order number: mc10h602/d mc10h602, mc100h602 9?bit latch ttl to ecl translator description the mc10h/100h602 is a 9 ? bit, dual supply ttl to ecl translator with latch. devices in the on semiconductor 9 ? bit translator series utilize the plcc ? 28 for optimal power pinning, signal flow ? through and electrical performance. the h602 features d ? type latches. latching is controlled by latch enable (len), while the master reset input resets the latches. a post ? latch logic enable is also provided (enecl), allowing control of the output state without destroying latch data. all control inputs are ecl level. the 10h version is compatible with mecl 10h ecl logic levels. the 100h version is compatible with 100k levels. features ? 9 ? bit ideal for byte ? parity applications ? flow ? through configuration ? extra ttl and ecl power/ground pins to minimize switching noise ? dual supply ? 3.5 ns max d to q ? pnp ttl inputs for low loading ? pb ? free packages are available* *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. marking diagram* xxx = 10 or 100 a = assembly location wl = wafer lot yy = year ww = work week g= pb ? free package plcc ? 28 fn suffix case 776 mcxxxh602g awlyyww 1 http://onsemi.com *for additional marking information, refer to application note and8002/d. see detailed ordering and shipping information in the package dimensions sect ion on page 4 of this data sheet. ordering information
mc10h602, mc100h602 http://onsemi.com 2 figure 1. plcc ? 28 pinout (top view) table 1. pin names pin function gnd v cce v cco v cct v ee d0 ? d8 q0 ? q8 enecl len mr ttl ground (0 v) ecl v cc (0 v) ecl v cc (0 v) ? outputs ttl supply (+ 5.0 v) ecl supply ( ? 5.2 / ? 4.5 v) data inputs (ttl) data outputs (ecl) enable control (ecl) latch enable (ecl) master reset (ecl) d6 567891011 25 24 23 22 21 20 19 d7 d8 gnd mr len enecl v cce q0 q1 v cco q2 v cco q3 26 27 28 2 3 4 18 17 16 14 13 12 15 d5 d4 v cct d3 d2 d1 d0 q8 q7 v cco q6 v ee q5 q4 figure 2. logic symbol dq en dq en dq en dq en dq en dq en dq en dq en dq en enecl d0 d1 d2 d3 d4 d5 d6 d7 d8 len mr q0 q1 q2 q3 q4 q5 q6 q7 q8 ttl ecl d l h x x x table 2. truth table len l l h x x mr l l l h x q l h q 0 l l enecl h h h h l table 3. dc characteristics: v cct = 5.0 v 10%; v ee = ? 5.2 v 5% (10h version); v ee = ? 4.2 v to ? 5.5 v (100h version) symbol parameter 0 c 25 c 75 c unit min max min max min max power supply current i ee ecl 10h 100h ? 125 ? 122 ? 125 ? 123 ? 125 ? 132 ma i cch i ccl ttl 48 50 48 50 48 50 ma note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously.
mc10h602, mc100h602 http://onsemi.com 3 table 4. 10h ecl dc characteristics: v cct = 5.0 v 10%; v ee = ? 5.2 v 5% symbol parameter condition 0 c 25 c 75 c unit min max min max min max i inh i inl input high current input low current 0.5 255 0.5 175 0.5 175 a a v ih v il input high voltage input low voltage ? 1170 ? 1950 ? 840 ? 1480 ? 1130 ? 1950 ? 810 ? 1480 ? 1070 ? 1950 ? 735 ? 1450 mv v oh v ol output high voltage output low voltage 50 to ? 2.0 v ? 1020 ? 1950 ? 840 ? 1630 ? 980 ? 1950 ? 810 ? 1630 ? 920 ? 1950 ? 735 ? 1600 mv note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. table 5. 100h ecl dc characteristics: v cct = 5.0 v 10%; v ee = ? 4.2 v to ? 5.5 v symbol parameter condition 0 c 25 c 75 c unit min max min max min max i inh i inl input high current input low current 0.5 255 0.5 175 0.5 175 a a v ih v il input high voltage input low voltage ? 1165 ? 1810 ? 880 ? 1475 ? 1165 ? 1810 ? 880 ? 1475 ? 1165 ? 1810 ? 880 ? 1475 mv v oh v ol output high voltage output low voltage 50 to ? 2.0 v ? 1025 ? 1810 ? 880 ? 1620 ? 1025 ? 1810 ? 880 ? 1620 ? 1025 ? 1810 ? 880 ? 1620 mv note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. table 6. ttl dc characteristics: v cct = 5.0 v 10%; v ee = ? 5.2 v 5% (10h version); v ee = ? 4.2 v to ? 5.5 v (100h version) symbol parameter condition 0 c 25 c 75 c unit min max min max min max v ih v il input high voltage input low voltage 2.0 0.8 2.0 0.8 2.0 0.8 v v i ih input high current v in = 2.7 v v in = 7.0 v 20 100 20 100 20 100 a i il input low current v in = 0.5 v ? 0.6 ? 0.6 ? 0.6 ma v ik input clamp voltage i in = ? 18 ma ? 1.2 ? 1.2 ? 1.2 v note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously.
mc10h602, mc100h602 http://onsemi.com 4 table 7. ac characteristics: v cct = 5.0 v 10%; v ee = ? 5.2 v 5% (10h version); v ee = ? 4.2 v to ? 5.5 v (100h version) symbol parameter 0 c 25 c 75 c unit min max min max min max t plh t phl propagation delay to output d len mr enecl 1.4 2.0 2.0 1.6 3.0 3.4 3.4 3.2 1.5 2.1 2.1 1.7 3.2 3.5 3.5 3.3 1.7 2.4 2.5 1.8 3.5 3.7 3.9 3.7 ns t s set ? up time, d to len 2.0 2.0 2.0 ns t h hold time, d to len 1.0 1.0 1.0 ns t w (l) len pulse width, low 2.0 2.0 2.0 ns t r t f output rise/fall time 20% ? 80% 0.5 1.5 0.5 1.5 0.5 1.5 ns note: device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printe d circuit board with maintained transverse airflow greater than 500 lfpm. electrical parameters are guaranteed only over the declared operating temperature range. functional operation of the device exceeding these conditions is not implied. device specification limit values are applied individually under normal operating conditions and not valid simultaneously. ordering information device package shipping ? mc10h602fn plcc ? 28 37 units / rail mc10h602fng plcc ? 28 (pb ? free) 37 units / rail mc10h602fnr2 plcc ? 28 500 / tape & reel mc10h602fnr2g plcc ? 28 (pb ? free) 500 / tape & reel mc100h602fn plcc ? 28 37 units / rail MC100H602FNG plcc ? 28 (pb ? free) 37 units / rail mc100h602fnr2 plcc ? 28 500 / tape & reel mc100h602fnr2g plcc ? 28 (pb ? free) 500 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d. resource reference of application notes an1405/d ? ecl clock distribution techniques an1406/d ? designing with pecl (ecl at +5.0 v) an1503/d ? eclinps i/o spice modeling kit an1504/d ? metastability and the eclinps family an1568/d ? interfacing between lvds and ecl an1672/d ? the ecl translator guide and8001/d ? odd number counters design and8002/d ? marking and date codes and8020/d ? termination of ecl logic devices and8066/d ? interfacing with eclinps and8090/d ? ac characteristics of ecl devices
mc10h602, mc100h602 http://onsemi.com 5 package dimensions plcc ? 28 fn suffix plastic plcc package case 776 ? 02 issue e ? n ? ? m ? ? l ? v w d d y brk 28 1 view s s l?m s 0.010 (0.250) n s t s l?m m 0.007 (0.180) n s t 0.004 (0.100) g1 g j c z r e a seating plane s l?m m 0.007 (0.180) n s t ? t ? b s l?m s 0.010 (0.250) n s t s l?m m 0.007 (0.180) n s t u s l?m m 0.007 (0.180) n s t z g1 x view d ? d s l?m m 0.007 (0.180) n s t k1 view s h k f s l?m m 0.007 (0.180) n s t notes: 1. datums ?l?, ?m?, and ?n? determined where top of lead shoulder exits plastic body at mold parting line. 2. dimension g1, true position to be measured at datum ?t?, seating plane. 3. dimensions r and u do not include mold flash. allowable mold flash is 0.010 (0.250) per side. 4. dimensioning and tolerancing per ansi y14.5m, 1982. 5. controlling dimension: inch. 6. the package top may be smaller than the package bottom by up to 0.012 (0.300). dimensions r and u are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 7. dimension h does not include dambar protrusion or intrusion. the dambar protrusion(s) shall not cause the h dimension to be greater than 0.037 (0.940). the dambar intrusion(s) shall not cause the h dimension to be smaller than 0.025 (0.635). dim min max min max millimeters inches a 0.485 0.495 12.32 12.57 b 0.485 0.495 12.32 12.57 c 0.165 0.180 4.20 4.57 e 0.090 0.110 2.29 2.79 f 0.013 0.019 0.33 0.48 g 0.050 bsc 1.27 bsc h 0.026 0.032 0.66 0.81 j 0.020 ??? 0.51 ??? k 0.025 ??? 0.64 ??? r 0.450 0.456 11.43 11.58 u 0.450 0.456 11.43 11.58 v 0.042 0.048 1.07 1.21 w 0.042 0.048 1.07 1.21 x 0.042 0.056 1.07 1.42 y ??? 0.020 ??? 0.50 z 2 10 2 10 g1 0.410 0.430 10.42 10.92 k1 0.040 ??? 1.02 ???
mc10h602, mc100h602 http://onsemi.com 6 on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5773 ? 3850 mc10h602/d eclinps is a trademark of semiconductor components industries, llc (scillc). mecl 10h is a trademark of motorola, inc. literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative
|
